View MC74VHC4066-D_5268154.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

quad analog switch/ multiplexer/demultiplexer highperformance silicongate cmos the mc74vhc4066 utilizes silicongate cmos technology to achieve fast propagation delays, low on resistances, and low offchannel leakage current. this bilateral switch/multiplexer/demultiplexer controls analog and digital voltages that may vary across the full powersupply range (from v cc to gnd). the vhc4066 is identical in pinout to the metalgate cmos mc14066 and the highspeed cmos hc4066a. each device has four independent switches. the device has been designed so that the on resistances (r on ) are much more linear over input voltage than r on of metalgate cmos analog switches. the on/off control inputs are compatible with standard cmos outputs; with pullup resistors, they are compatible with lsttl outputs. for analog switches with voltagelevel translators, see the vhc4316. ? fast switching and propagation speeds ? high on/off output voltage ratio ? low crosstalk between switches ? diode protection on all inputs/outputs ? wide powersupply voltage range (v cc gnd) = 2.0 to 12.0 volts ? analog input voltage range (v cc gnd) = 2.0 to 12.0 volts ? improved linearity and lower on resistance over input voltage than the mc14016 or mc14066 ? low noise ? chip complexity: 44 fets or 11 equivalent gates x a y a 12 a on/off control 13 x b y b 43 b on/off control 5 x c y c 89 c on/off control 6 x d y d 11 10 d on/off control 12 analog outputs/inputs analog inputs/outputs = x a , x b , x c , x d pin 14 = v cc pin 7 = gnd figure 1. logic diagram on semiconductor mc74vhc4066 function table pin assignment 11 12 13 14 8 9 10 5 4 3 2 1 7 6 y d x d d on/off control a on/off control v cc x c y c x b y b y a x a gnd c on/off control b on/off control on/off control state of input analog switch loff hon ordering information mc74vhcxxxxd mc74vhcxxxxdt soic tssop d suffix 14lead soic package case 751a03 dt suffix 14lead tssop package case 948g01 ? semiconductor components industries, llc, 2001 april, 2001 rev. 4 1 publication order number: mc74vhc4066/d
http://onsemi.com 2 ??????????????????????? ??????????????????????? maximum ratings* ???? ???? symbol ?????????????? ?????????????? parameter ????? ????? value ??? ??? unit ???? ???? v cc ?????????????? ?????????????? positive dc supply voltage (referenced to gnd) ????? ????? 0.5 to + 14.0 ??? ??? v ???? ???? v is ?????????????? ?????????????? analog input voltage (referenced to gnd) ????? ????? 0.5 to v cc + 0.5 ??? ??? v ???? ???? v in ?????????????? ?????????????? digital input voltage (referenced to gnd) ????? ????? 0.5 to v cc + 0.5 ??? ??? v ???? ???? i ?????????????? ?????????????? dc current into or out of any pin ????? ????? 25 ??? ??? ma ???? ???? p d ?????????????? ?????????????? power dissipation in still air, soic package2 tssop package2 ????? ????? 500 450 ??? ??? mw ???? ???? t stg ?????????????? ?????????????? storage temperature ????? ????? 65 to + 150 ??? ??? c ???? ???? t l ?????????????? ?????????????? lead temperature, 1 mm from case for 10 seconds ????? ????? 260 ??? ??? c *maximum ratings are those values beyond which damage to the device may occur. functional operation should be restricted to the recommended operating conditions. 2derating e soic package: 7 mw/ c from 65 to 125 c tssop package: 6.1 mw/ c from 65 to 125 c recommended operating conditions ???? ???? symbol ??????????????? ??????????????? parameter ??? ??? min ?? ?? max ??? ??? unit ???? ???? v cc ??????????????? ??????????????? positive dc supply voltage (referenced to gnd) ??? ??? 2.0 ?? ?? 12.0 ??? ??? v ???? ???? v is ??????????????? ??????????????? analog input voltage (referenced to gnd) ??? ??? gnd ?? ?? v cc ??? ??? v ???? ???? v in ??????????????? ??????????????? digital input voltage (referenced to gnd) ??? ??? gnd ?? ?? v cc ??? ??? v ???? ???? v io * ??????????????? ??????????????? static or dynamic voltage across switch ??? ??? e ?? ?? 1.2 ??? ??? v ???? ???? t a ??????????????? ??????????????? operating temperature, all package types ??? ??? 55 ?? ?? + 125 ??? ??? c ???? ? ?? ? ? ?? ? ? ?? ? ???? t r , t f ??????????????? ? ????????????? ? ? ????????????? ? ? ????????????? ? ??????????????? input rise and fall time, on/off control inputs (figure 14) v cc = 2.0 v v cc = 3.0 v v cc = 4.5 v v cc = 9.0 v v cc = 12.0 v ??? ? ? ? ? ? ? ? ? ? ??? 0 0 0 0 0 ?? ?? ?? ?? ?? 1000 600 500 400 250 ??? ? ? ? ? ? ? ? ? ? ??? ns *for voltage drops across the switch greater than 1.2 v (switch on), excessive v cc current may be drawn; i.e., the current out of the switch may contain both v cc and switch input components. the reliability of the device will be unaffected unless the maximum ratings are exceeded. dc electrical characteristic digital section (voltages referenced to gnd) ???? ???? ????????? ????????? ?????????? ?????????? ??? ??? ????????? ????????? guaranteed limit ??? ??? ???? ? ?? ? ???? symbol ????????? ? ??????? ? ????????? parameter ?????????? ? ???????? ? ?????????? test conditions ??? ? ? ? ??? v cc v ???? ? ?? ? ???? 55 to 25 c ??? ? ? ? ??? 85 c ???? ? ?? ? ???? 125 c ??? ? ? ? ??? unit ???? ? ?? ? ? ?? ? ???? v ih ????????? ? ??????? ? ? ??????? ? ????????? minimum highlevel voltage on/off control inputs ?????????? ? ???????? ? ? ???????? ? ?????????? r on = per spec ??? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 1.5 2.1 3.15 6.3 8.4 ??? ? ? ? ? ? ? ??? 1.5 2.1 3.15 6.3 8.4 ???? ? ?? ? ? ?? ? ???? 1.5 2.1 3.15 6.3 8.4 ??? ? ? ? ? ? ? ??? v ???? ? ?? ? ? ?? ? ? ?? ? ???? v il ????????? ? ??????? ? ? ??????? ? ? ??????? ? ????????? maximum lowlevel voltage on/off control inputs ?????????? ? ???????? ? ? ???????? ? ? ???????? ? ?????????? r on = per spec ??? ? ? ? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? 0.5 0.9 1.35 2.7 3.6 ??? ? ? ? ? ? ? ? ? ? ??? 0.5 0.9 1.35 2.7 3.6 ???? ? ?? ? ? ?? ? ? ?? ? ???? 0.5 0.9 1.35 2.7 3.6 ??? ? ? ? ? ? ? ? ? ? ??? v ???? ? ?? ? ???? i in ????????? ? ??????? ? ????????? maximum input leakage current on/off control inputs ?????????? ? ???????? ? ?????????? v in = v cc or gnd ??? ? ? ? ??? 12.0 ???? ? ?? ? ???? 0.1 ??? ? ? ? ??? 1.0 ???? ? ?? ? ???? 1.0 ??? ? ? ? ??? m a ???? ???? i cc ????????? ????????? maximum quiescent supply current (per package) ?????????? ?????????? v in = v cc or gnd v io = 0 v ??? ??? 6.0 12.0 ???? ???? 2 4 ??? ??? 20 40 ???? ???? 40 160 ??? ??? m a this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance cir- cuit. for proper operation, v in and v out should be constrained to the range gnd (v in or v out ) v cc . unused inputs must always be tied to an appropriate logic voltage level (e.g., either gnd or v cc ). unused outputs must be left open. i/o pins must be connected to a properly terminated line or bus.
http://onsemi.com 3 dc electrical characteristics analog section (voltages referenced to gnd) ???? ???? ????????? ????????? ?????????? ?????????? ??? ??? ????????? ????????? guaranteed limit ??? ??? ???? ???? symbol ????????? ????????? parameter ?????????? ?????????? test conditions ??? ??? v cc v ???? ???? 55 to 25 c ??? ??? 85 c ???? ???? 125 c ??? ??? unit ???? ? ?? ? ? ?? ? ? ?? ? ???? r on ????????? ? ??????? ? ? ??????? ? ? ??????? ? ????????? maximum aono resistance ?????????? ? ???????? ? ? ???????? ? ? ???????? ? ?????????? v in = v ih v is = v cc to gnd i s 2.0 ma (figures 2 through 7) ??? ? ? ? ? ? ? ? ? ? ??? 2.02 3.02 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? e e 120 70 70 ??? ? ? ? ? ? ? ? ? ? ??? e e 160 85 85 ???? ? ?? ? ? ?? ? ? ?? ? ???? e e 200 100 100 ??? ? ? ? ? ? ? ? ? ? ??? w ???? ? ?? ? ? ?? ? ???? ????????? ? ??????? ? ? ??????? ? ????????? ?????????? ? ???????? ? ? ???????? ? ?????????? v in = v ih v is = v cc or gnd (endpoints) i s 2.0 ma (figures 2 through 7) ??? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? e e 70 50 30 ??? ? ? ? ? ? ? ??? e e 85 60 60 ???? ? ?? ? ? ?? ? ???? e e 100 80 80 ??? ? ? ? ? ? ? ??? ???? ? ?? ? ? ?? ? ???? d r on ????????? ? ??????? ? ? ??????? ? ????????? maximum difference in aono resistance between any two channels in the same package ?????????? ? ???????? ? ? ???????? ? ?????????? v in = v ih v is = 1/2 (v cc gnd) i s 2.0 ma ??? ? ? ? ? ? ? ??? 2.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? e 20 15 15 ??? ? ? ? ? ? ? ??? e 25 20 20 ???? ? ?? ? ? ?? ? ???? e 30 25 25 ??? ? ? ? ? ? ? ??? w ???? ? ?? ? ? ?? ? ???? i off ????????? ? ??????? ? ? ??????? ? ????????? maximum offchannel leakage current, any one channel ?????????? ? ???????? ? ? ???????? ? ?????????? v in = v il v io = v cc or gnd switch off (figure no tag) ??? ? ? ? ? ? ? ??? 12.0 ???? ? ?? ? ? ?? ? ???? 0.1 ??? ? ? ? ? ? ? ??? 0.5 ???? ? ?? ? ? ?? ? ???? 1.0 ??? ? ? ? ? ? ? ??? m a ???? ? ?? ? ???? i on ????????? ? ??????? ? ????????? maximum onchannel leakage current, any one channel ?????????? ? ???????? ? ?????????? v in = v ih v is = v cc or gnd (figure no tag) ??? ? ? ? ??? 12.0 ???? ? ?? ? ???? 0.1 ??? ? ? ? ??? 0.5 ???? ? ?? ? ???? 1.0 ??? ? ? ? ??? m a 2at supply voltage (v cc ) approaching 3 v the analog switchon resistance becomes extremely nonlinear. therefore, for lowvoltage operation, it is recommended that these devices only be used to control digital signals. ac electrical characteristics (c l = 50 pf, on/off control inputs: t r = t f = 6 ns) ????? ????????????????? ??? ????????? guaranteed limit ??? ????? ? ??? ? ????? symbol ????????????????? ? ??????????????? ? ????????????????? parameter ??? ? ? ? ??? v cc v ???? ? ?? ? ???? 55 to 25 c ??? ? ? ? ??? 85 c ???? ? ?? ? ???? 125 c ??? ? ? ? ??? unit ????? ? ??? ? ? ??? ? ? ??? ? ????? t plh , t phl ????????????????? ? ??????????????? ? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, analog input to analog output (figures 18 and 13) ??? ? ? ? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? 40 30 5 5 5 ??? ? ? ? ? ? ? ? ? ? ??? 50 40 7 7 7 ???? ? ?? ? ? ?? ? ? ?? ? ???? 60 50 8 8 8 ??? ? ? ? ? ? ? ? ? ? ??? ns ????? ? ??? ? ? ??? ? ????? t plz , t phz ????????????????? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, on/off control to analog output (figures 14 and 15) ??? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 80 60 20 20 20 ??? ? ? ? ? ? ? ??? 90 70 25 25 25 ???? ? ?? ? ? ?? ? ???? 110 80 35 35 35 ??? ? ? ? ? ? ? ??? ns ????? ? ??? ? ? ??? ? ? ??? ? ????? t pzl , t pzh ????????????????? ? ??????????????? ? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, on/off control to analog output (figures 14 and 15) ??? ? ? ? ? ? ? ? ? ? ??? 2.0 3.0 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? 80 45 20 20 20 ??? ? ? ? ? ? ? ? ? ? ??? 90 50 25 25 25 ???? ? ?? ? ? ?? ? ? ?? ? ???? 100 60 30 30 30 ??? ? ? ? ? ? ? ? ? ? ??? ns ????? ????? c ????????????????? ????????????????? maximum capacitance on/off control input ??? ??? e ???? ???? 10 ??? ??? 10 ???? ???? 10 ??? ??? pf ????? ? ??? ? ????? ????????????????? ? ??????????????? ? ????????????????? control input = gnd analog i/o feedthrough ??? ? ? ? ??? e e ???? ? ?? ? ???? 35 1.0 ??? ? ? ? ??? 35 1.0 ???? ? ?? ? ???? 35 1.0 ??? ? ? ? ??? typical @ 25 c, v cc = 5.0 v c pd power dissipation capacitance (per switch) (figure 17)* 15 pf * used to determine the noload dynamic power consumption: p d = c pd v cc 2 f + i cc v cc .
http://onsemi.com 4 additional application characteristics (voltages referenced to gnd unless noted) ???? ? ?? ? ???? symbol ?????????? ? ???????? ? ?????????? parameter ?????????????? ? ???????????? ? ?????????????? test conditions ??? ? ? ? ??? v cc v ???? ? ?? ? ???? limit* 25 c 74hc ??? ? ? ? ??? unit ???? ? ?? ? ? ?? ? ? ?? ? ???? bw ?????????? ? ???????? ? ? ???????? ? ? ???????? ? ?????????? maximum onchannel bandwidth or minimum frequency response (figure no tag) ?????????????? ? ???????????? ? ? ???????????? ? ? ???????????? ? ?????????????? f in = 1 mhz sine wave adjust f in voltage to obtain 0 dbm at v os increase f in frequency until db meter reads 3 db r l = 50 w , c l = 10 pf ??? ? ? ? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? 150 160 160 ??? ? ? ? ? ? ? ? ? ? ??? mhz ???? ? ?? ? ???? e ?????????? ? ???????? ? ?????????? offchannel feedthrough isolation (figure no tag) ?????????????? ? ???????????? ? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 50 50 50 ??? ? ? ? ??? db ???? ? ?? ? ???? ?????????? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 40 40 40 ??? ? ? ? ??? ???? ? ?? ? ? ?? ? ???? e ?????????? ? ???????? ? ? ???????? ? ?????????? feedthrough noise, control to switch (figure no tag) ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? v in 1 mhz square wave (t r = t f = 6 ns) adjust r l at setup so that i s = 0 a r l = 600 w , c l = 50 pf ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 60 130 200 ??? ? ? ? ? ? ? ??? mv pp ???? ? ?? ? ???? ?????????? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ?????????????? r l = 10 k w , c l = 10 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 30 65 100 ??? ? ? ? ??? ???? ? ?? ? ???? e ?????????? ? ???????? ? ?????????? crosstalk between any two switches (figure 16) ?????????????? ? ???????????? ? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 70 70 70 ??? ? ? ? ??? db ???? ? ?? ? ? ?? ? ???? ?????????? ? ???????? ? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 80 80 80 ??? ? ? ? ? ? ? ??? ???? ? ?? ? ? ?? ? ???? thd ?????????? ? ???????? ? ? ???????? ? ?????????? total harmonic distortion (figure 20) ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? f in = 1 khz, r l = 10 k w , c l = 50 pf thd = thd measured thd source v is = 4.0 v pp sine wave v is = 8.0 v pp sine wave v is = 11.0 v pp sine wave ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 0.10 0.06 0.04 ??? ? ? ? ? ? ? ??? % *guaranteed limits not tested. determined by design and verified by qualification. figure 2. typical on resistance, v cc = 2.0 v 0 50 100 150 200 250 300 350 400 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00 +25 c +125 c 55 c v is , input voltage (volts), referenced to ground ron @ 2 v
http://onsemi.com 5 0 20 40 60 80 100 120 140 160 180 200 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 v is , input voltage (volts), referenced to ground ron @ 4.5 v +25 c +125 c 55 c figure 3. typical on resistance, v cc = 4.5 v figure 4. typical on resistance, v cc = 6.0 v 0 10 20 30 40 50 60 70 80 90 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 +25 c +125 c 55 c v is , input voltage (volts), referenced to ground ron @ 6 v
http://onsemi.com 6 figure 5. typical on resistance, v cc = 9.0 v v is , input voltage (volts), referenced to ground ron @ 9v 0 10 20 30 40 50 60 70 80 90 0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 +25 c +125 c 55 c figure 6. typical on resistance, v cc = 12 v 0 10 20 30 40 50 60 0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 9.00 10.00 11.00 12.00 v is , input voltage (volts), referenced to ground ron @ 12 v +25 c +125 c 55 c
http://onsemi.com 7 figure 7. on resistance test setup plotter mini computer programmable power supply dc analyzer v cc + - analog in common out gnd device under test figure 8. maximum off channel leakage current, any one channel, test setup off 7 14 v cc a v cc gnd v cc selected control input v il figure 9. maximum on channel leakage current, test setup on 14 v cc n/c a gnd v cc 7 selected control input v ih figure 10. maximum onchannel bandwidth test setup on 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os 7 selected control input v cc figure 11. offchannel feedthrough isolation, test setup off 7 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os r l v is selected control input figure 12. feedthrough noise, on/off control to analog out, test setup 14 v cc c l * *includes all probe and jig capacitance. off/on v cc gnd v in 1 mhz t r = t f = 6 ns control v cc/2 r l i s r l v os 7 selected control input v cc/2
http://onsemi.com 8 positionwhen testing t plz and t pzl figure 13. propagation delay test setup on 14 v cc *includes all probe and jig capacitance. test point analog out analog in c l * 7 selected control input v cc t r t f v cc gnd high impedance v ol v oh high impedance control analog out 90% 50% 10% 50% 50% 10% 90% t pzh t phz t pzl t plz figure 14. propagation delay, on/off control to analog out on/off v cc test point 14 v cc 1 k w positionwhen testing t phz and t pzh c l * 1 2 1 2 figure 15. propagation delay test setup 1 2 7 selected control input figure 16. crosstalk between any two switches, test setup r l on 14 v cc or gnd c l * *includes all probe and jig capacitance. off r l r l v is r l c l * v os f in 0.1 m f v cc/2 v cc/2 7 selected control input v cc/2 figure 17. power dissipation capacitance test setup 14 v cc n/c off/on a n/c 7 selected control input on/off control *includes all probe and jig capacitance. v cc v cc gnd analog in analog out 50% t plh t phl 50% figure 18. propagation delays, analog in to analog out
http://onsemi.com 9 0 -10 -20 -30 -40 -50 1.0 2.0 frequency (khz) dbm -60 -70 -80 -90 fundamental frequency device source figure 19. plot, harmonic distortion 3.0 on v cc 0.1 m f c l * f in r l to distortion meter *includes all probe and jig capacitance. v os v is 7 selected control input v cc figure 20. total harmonic distortion, test setup v cc/2 application information the on/off control pins should be at v cc or gnd logic levels, v cc being recognized as logic high and gnd being recognized as a logic low. unused analog inputs/outputs may be left floating (not connected). however, it is advisable to tie unused analog inputs and outputs to v cc or gnd through a low value resistor. this minimizes crosstalk and feedthrough noise that may be pickedup by the unused i/o pins. the maximum analog voltage swings are determined by the supply voltages v cc and gnd. the positive peak analog voltage should not exceed v cc . similarly, the negative peak analog voltage should not go below gnd. in the example below, the difference between v cc and gnd is twelve volts. therefore, using the configuration in figure 21, a maximum analog signal of twelve volts peaktopeak can be controlled. when voltage transients above v cc and/or below gnd are anticipated on the analog channels, external diodes (dx) are recommended as shown in figure 22. these diodes should be small signal, fast turnon types able to absorb the maximum anticipated current surges during clipping. an alternate method would be to replace the dx diodes with mosorbs (high current surge protectors). mosorbs are fast turnon devices ideally suited for precise dc protection with no inherent wear out mechanism. analog o/i on 14 v cc = 12 v analog i/o + 12 v 0 v + 12 v 0 v other control inputs (v cc or gnd) on 16 v cc d x d x v cc d x figure 21. 12 v application figure 22. transient suppressor application 7 selected control input d x other control inputs (v cc or gnd) 7 selected control input v cc
http://onsemi.com 10 +5 v 14 vhc4066 control inputs 7 5 6 14 15 lsttl/ nmos analog signals r* r* r* r* analog signals vhct buffer r* = 2 to 10 k w v dd = 5 v v cc = 5 to 12 v analog signals analog signals 116 14 control inputs 7 8 mc14504 13 3 5 7 9 11 14 2 4 6 10 5 6 14 15 channel 4 channel 3 channel 2 channel 1 1 of 4 switches common i/o 1234 control inputs input output 0.01 m f lf356 or equivalent a. using pull-up resistors b. using hct buffer figure 23. lsttl/nmos to hcmos interface figure 24. ttl/nmostocmos level converter analog signal peaktopeak greater than 5 v (also see vhc4316) figure 25. 4input multiplexer figure 26. sample/hold amplifier + - 1 of 4 switches +5 v 14 control inputs 7 5 6 14 15 lsttl/ nmos analog signals analog signals 1 of 4 switches 1 of 4 switches 1 of 4 switches vhc4066 vhc4066
http://onsemi.com 11 outline dimensions case 751a03 issue f soic14 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. a b g p 7 pl 14 8 7 1 m 0.25 (0.010) b m s b m 0.25 (0.010) a s t t f r x 45 seating plane d 14 pl k c j m dim min max min max inches millimeters a 8.55 8.75 0.337 0.344 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.228 0.244 r 0.25 0.50 0.010 0.019 d suffix case 948g01 issue o tssop dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c --- 1.20 --- 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane -w-. s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l u seating plane 0.10 (0.004) t ??? ??? ??? section nn detail e j j1 k k1 detail e f m w 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t v 14x ref k n n dt suffix
http://onsemi.com 12 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information central/south america: spanish phone : 3033087143 (monfri 8:00am to 5:00pm mst) email : onlitspanish@hibbertco.com tollfree from mexico: dial 018002882872 for access then dial 8662979322 asia/pacific : ldc for on semiconductor asia support phone : 13036752121 (tuefri 9:00am to 1:00pm, hong kong time) toll free from hong kong & singapore: 00180044223781 email : onlitasia@hibbertco.com japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402700 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. mc74vhc4066/d north america literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com fax response line: 3036752167 or 8003443810 toll free usa/canada n. american technical support : 8002829855 toll free usa/canada europe: ldc for on semiconductor european support german phone : (+1) 3033087140 (monfri 2:30pm to 7:00pm cet) email : onlitgerman@hibbertco.com french phone : (+1) 3033087141 (monfri 2:00pm to 7:00pm cet) email : onlitfrench@hibbertco.com english phone : (+1) 3033087142 (monfri 12:00pm to 5:00pm gmt) email : onlit@hibbertco.com european tollfree access*: 0080044223781 *available from germany, france, italy, uk, ireland

▲Up To Search▲

Price & Availability of MC74VHC4066-D

	To Download MC74VHC4066-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .